Walk-On Rooflight Installation

Imposed loads, and who specifies the build up

The glass build-up in a walk-on unit is calculated from the load it has to carry. Which means the first question on any glass floor is not what glass to use, but what is going to happen on it, and who is going to decide.

What an imposed load is

Structural loads divide into two categories and both apply here.

Dead load is permanent: the weight of the glass itself, the frame, and anything built on it. It is known precisely and it never changes.

Imposed load is what the building is used for: people, furniture, whatever gets put on the surface. It is variable, it is uncertain, and it is what codes exist to define.

A walk-on unit is designed for both together, plus wind and snow where it is part of a roof.

Loads are set by use, not by product

This is the point that decides everything downstream.

Design codes assign a load to a category of use rather than to a component. A domestic floor, a balcony, an area of assembly and a space with public access are all different figures, and they differ by a great deal rather than a little.

So the same physical unit, in the same opening, needs a different build-up depending on whether it is a private terrace off a bedroom or a communal roof terrace serving six flats. The glass does not know the difference; the code does.

The categories that arise on our work

What changes the load category
Situation Typically Why it matters
Private domestic floor or terrace The lowest domestic figure The common case on our work
Balcony to a dwelling Higher than a floor People congregate at an edge
Communal terrace to flats Higher again Shared access, more people
Access for maintenance only A restricted case Only where genuinely restricted and marked
Any public access Substantially higher Different world entirely

The figures themselves come from the code and from the engineer applying it. What matters for the conversation is that these are different problems and the difference is decided at the briefing stage.

Concentrated loads

The one people forget, and it frequently governs rather than the distributed load.

A code specifies both a distributed load spread over the area and a concentrated load applied over a small patch, representing a point contact: a stiletto heel, a chair leg, a ladder foot, a dropped tool.

On a glass panel a concentrated load in the middle produces very different stresses from the same total weight spread out, and on a stiff plate it is frequently the concentrated case that sizes the build-up.

It is also the one that changes with use in ways nobody anticipates. A terrace that acquires a barbecue on legs, or a planter, has acquired a concentrated load.

Daylight falling through a glass floor panel into the room below, a soft rectangle of light on a plain floor, seen from inside
Impact, and the accidental case

Impact, and the accidental case

Beyond the static loads there is the question of what happens when something hits it.

A dropped object, somebody falling onto it, something blown against it in a storm. Design for those is about post-breakage behaviour rather than about strength: the unit is expected to survive as a safe assembly rather than to be undamaged.

Which is the argument for the sacrificial top ply and the multiple plies below, and it is why a walk-on build-up is not simply thicker glass.

Who specifies it

The answer is a structural engineer or a specialist manufacturer’s technical department, working from the loads for the actual use and the actual span. Not a catalogue, and not an installer.

What they need is the span in both directions, the support conditions on all four edges, the use category, the exposure, and anything unusual about the situation. What they produce is a build-up, a support specification and calculations.

That output is what gets ordered and what Building Control sees. Anything less is a selection rather than a design.

The question to ask a supplier

One question separates a specified unit from a chosen one.

What load has this build-up been designed for, and over what span?

A supplier who can answer with a figure and a span is quoting an engineered product. A supplier who says it is walk-on rated, without a load or a span, is describing a category rather than a specification, and the two are not the same.

It is a reasonable question, it takes a sentence to answer, and it is the single most useful thing a customer can ask about this product.

Span is half the answer

A load figure without a span means very little, and this is where catalogue specification falls down.

The same build-up spanning a metre and spanning two and a half metres is carrying completely different bending stresses and deflecting by completely different amounts. Doubling a span does far more than double the demand.

Which is why a unit that is genuinely walk-on at one size is not necessarily walk-on at a larger one, and why enlarging an opening on a glass floor is a redesign rather than a resize.

A first floor terrace with a walk on glass panel set flush into timber decking, coastal light, plain boundary wall behind, no people
Use changes, and nobody tells anybody

Use changes, and nobody tells anybody

The realistic risk on a domestic glass floor over its life.

A private terrace becomes a space where a family entertains. A light well cover in a garden becomes somewhere a heavy planter sits. A landing panel acquires a bookcase at its edge. A house is sold and the next owner has different habits entirely.

None of that is anybody’s fault and the design should anticipate it. Which is an argument for specifying to the realistic use rather than the minimum, because the margin between categories is not usually a large proportion of the cost and it is the only insurance against a change of use nobody records.

Guarding, and where the floor stops

Adjacent to the load question and frequently forgotten.

Where a glass floor forms part of a balcony or a terrace, the edge protection around it is a separate requirement with its own loads: a barrier has to resist a horizontal load applied at a defined height, and that load also depends on the use category.

Where the glass floor is set within a larger deck, the guarding is at the deck perimeter rather than around the glass. Where the glass is at the edge, the two interact and both are part of the same design.

What Building Control wants

  1. The use category and the loads adopted.
  2. Calculations for the glass build-up against those loads and that span.
  3. The support and bearing specification.
  4. The structure beneath, and evidence it carries the new loads.
  5. Slip resistance for the walking surface.
  6. Guarding where the situation requires it.

Which is a fuller submission than an ordinary rooflight, and reasonably so.

Retrofitting into an existing opening

The situation where the load question bites hardest.

An existing rooflight opening was formed to carry a rooflight: weather loads and a light unit. A walk-on unit adds substantial dead weight and then imposed loads on top of it, into trimmers and a structure sized for neither.

Which means the existing structure is assessed and frequently strengthened, and that assessment comes before any conversation about glass. On a good proportion of retrofits it is the work rather than an accompaniment to it.

The honest position on cost

We publish no prices, and the shape is worth describing because people underestimate it.

The glass is expensive. The engineering is a real cost. The structural work beneath is frequently the largest item. The lifting and access to get the unit in place is substantial. And the detailing around it, drainage and weathering, is skilled work.

A walk-on unit is not an expensive rooflight. It is a small structural project with a rooflight in it, and anybody quoting it as a product swap has not priced the job.

The bearing edge of a walk on glass unit where it lands on its frame, seen close from the side, the laminate interlayers visible in the edge of the glass
Snow and wind, where the unit is also a roof

Snow and wind, where the unit is also a roof

A walk-on unit set in a roof rather than a floor carries the weather loads as well, and they combine with the imposed load rather than replacing it.

Snow lying on a glass floor is a distributed load that arrives without anybody choosing it, and on the higher ground toward the Downs it is a real if occasional case. Wind produces uplift on a roof unit, which is a load in the opposite direction from everything else on this page and which the fixings rather than the glass have to resist.

Where the unit is set flush in a terrace deck at first floor level, it is doing both jobs at once: a floor above and a roof below. The engineer combines those cases, and it is one more reason the design cannot be lifted from a product sheet.

Where we would advise against it

Being even handed, because it is a product people want for good reasons and it is not always the answer.

Where the existing structure would need substantial work and the benefit is modest, a non-trafficked unit in the same position with the traffic routed around it achieves most of the daylight for a fraction of the cost. Where the span is large, the build-up and everything under it escalates quickly.

We will set out both and say which we think is the better value, even where the smaller option is the smaller job.

Recording what it was designed for

A glass floor outlives the memory of what it was specified for, and that is a genuine safety issue rather than a paperwork one.

The load category, the span, the build-up and the calculations belong with the building’s paperwork, handed to the owner and passed on at a sale. Twenty years from now somebody will want to put something heavy on it, or convert the space, and there will be no other way to know what it can take.

Where a unit was specified for restricted access rather than general use, that fact especially has to survive, because a restricted access panel that somebody later treats as a floor is the failure mode this whole page exists to prevent.

What we want to know on walk on glass

We ask what will happen on it and who will have access before anything else, because that sets the load category and everything follows from it. We work to an engineered build-up with a stated load and span rather than a catalogue description, check the structure beneath before the glass above, and put the calculations to Building Control.

Where a customer is comparing two quotations and one is markedly cheaper, the load and span question is usually where the difference is. A unit designed for a domestic floor and one designed for a communal terrace are different products at different prices, and a quotation that does not say which it is has not been priced against the same brief.

Ask any supplier what load and what span. If the answer is a category rather than a figure, keep asking.

Thinking about this job? We survey across Worthing, West Sussex and the South Downs and give you a fixed price before any work starts, with a 10-year workmanship guarantee.

Get a fixed quote

Get a fixed quote

Tell us about the roof. We will tell you the price.

A survey costs you nothing and there is no obligation attached to it. We look at the roof build-up, the exposure and the opening, and give you one fixed figure, not an estimate that moves once work starts.

If your rooflight is leaking now, say so and we will prioritise the survey.

  • Fixed price, confirmed in writing
  • 10-year workmanship guarantee
  • Installed to current Building Regulations
  • Your roof is never left open overnight
Call Get a fixed quote