Roof Window Installation

Do roof windows need building regulations?

Yes, a new opening is notifiable work. What is specific to a roof window, as against a flat roof unit, is the structural trimming between rafters and the escape requirement where a loft room is a bedroom. Those two decide the specification long before the thermal or ventilation checks do.

Where the general position is set out

The notification routes, the certificate and what happens if work was never notified apply identically to every rooflight.

They are on do flat rooflights need building control, and everything there applies to a roof window.

This page is the two things that do not.

Trimming between rafters

The structural item, and on a cut roof it is real carpentry.

Rafters cut for the opening are carried by trimmers spanning to the rafters either side, which then take the load the cut rafters were carrying.

The trimmers are sized for that span and load, and on anything beyond a single rafter it is a designed detail rather than a site decision.

Why a pitched roof differs from a deck

Because the load runs down the slope rather than across a flat plane.

A trimmer in a pitched roof carries load along the rafters and transfers it laterally, and the fixings work in a different direction from those in a flat deck.

It is ordinary work and it is not the same detail.

On a trussed roof

Where the structural question largely disappears. No member is cut, so the check is that the framing within the bay is adequate to carry the window and the covering battens around it.

What fits is on can a roof window be fitted between trusses.

Cutting a truss

Where it becomes a structural design rather than a rooflight job.

Altering a trussed rafter requires a designed replacement for what it was doing, calculated and specified, and building control will want to see that.

It is why a wider unit on a trussed roof is a different order of project.

Close detail of lead soakers and an apron flashing being dressed into a Sussex clay peg tile roof around a roof window, the irregular hand made gauge of the tiles clearly visible
Escape, which decides the unit

Escape, which decides the unit

The second item specific to a roof window, and it comes first in practice.

Where a loft room is a habitable bedroom, one window has to provide a stated clear opening at a stated sill height, and that determines the size and the opening action.

The requirements are on can a roof window be an escape window.

Why escape is checked first

Because it constrains the product rather than the workmanship.

Thermal performance and ventilation are satisfied by any reasonable current unit. Escape is satisfied only by particular sizes and actions, so it narrows the choice before anything else.

Escape and the finished floor

The detail that catches loft conversions out.

The sill height is measured to the finished floor, which on a conversion is being built, so the window position and the floor level have to be agreed together.

Getting one fixed before the other is how a compliant window ends up too high.

Insulation at the reveal

The condensation provision, and on a pitched roof it has its own geometry.

A roof window sits in a sloping build up, so the reveal is deeper at the head than at the sill and the insulation has to be carried around all four sides of a non-rectangular void.

Left short at the head, which is where it is hardest to reach, water forms along the top of the frame.

The ventilation path above the insulation

A pitched roof requirement that a flat deck does not share in the same way.

On a cold roof, air moves from the eaves to the ridge above the insulation, and an opening cut into that must not block the path.

Where it does, the roof space runs damp and the window gets blamed for it.

Where the loft is habitable

The insulation line moves, and the detail changes with it.

In a converted loft the insulation follows the rafters rather than the ceiling, so the frame sits in a warm roof and the vapour control layer has to be sealed to it.

What that means is on the Findon Valley page, where chalet roofs are the dominant condition.

The inside of a trussed rafter roof space, W shaped webs and punched metal plate joints clearly visible at the intersections, daylight from a gable vent
As part of a loft conversion

As part of a loft conversion

Where the notification is already in hand.

A conversion is notifiable in its own right and the windows are part of it, assessed alongside the floor, the stair and the fire strategy rather than separately.

Which of the two applies is agreed at the start.

When the inspector wants to see it

With the opening formed and the trimming visible, before it is closed up.

On a roof window that is the only chance to see the structural work, so the job is sequenced around the visit rather than boarded and inspected afterwards.

Replacements

Not normally notifiable, and the thermal standard still applies.

Swapping a unit into an existing opening alters no structure, so nobody inspects it, and the obligation to meet the standard is unchanged.

What a purlin does to the trimming

A cut roof complication that a flat deck never has.

A purlin runs horizontally beneath the rafters and carries them, and a window opening that crosses one means the purlin is in the way rather than the rafters.

A purlin is not trimmed around casually. The window position moves up or down the slope instead, which is why the purlin line is established from inside before anything is offered.

Fire spread between properties

A consideration on a close boundary that a rear extension rarely raises.

Where a roof slope is close to a boundary, there are limits on unprotected openings, and a large area of glass in that slope can engage them.

On a detached or semi-detached house it almost never arises. On a narrow terraced plot it is worth establishing.

What we settle first on a pitched roof

We settle the escape question before anything is specified, design the trimming for the actual span, and sequence the job so the structure is inspected before it is closed up.

The whole picture is on the roof window installation page.

Thinking about this job? We survey across Worthing, West Sussex and the South Downs and give you a fixed price before any work starts, with a 10-year workmanship guarantee.

Get a fixed quote

Get a fixed quote

Tell us about the roof. We will tell you the price.

A survey costs you nothing and there is no obligation attached to it. We look at the roof build-up, the exposure and the opening, and give you one fixed figure, not an estimate that moves once work starts.

If your rooflight is leaking now, say so and we will prioritise the survey.

  • Fixed price, confirmed in writing
  • 10-year workmanship guarantee
  • Installed to current Building Regulations
  • Your roof is never left open overnight
Call Get a fixed quote