Rainfall noise on a flat glass unit, and what reduces it
Rain on a rooflight is the most common complaint about a product that has nothing wrong with it. It is also one of the few rooflight characteristics that can be improved a great deal at the specification stage and almost not at all afterwards.
This page sets out why overhead glazing is loud, what makes some units much louder than others, and what actually reduces it.
Why overhead glass is louder than a window
A vertical window takes rain at a glancing angle. Most of the water runs down the face rather than striking it, and the energy of each drop is largely converted into flow rather than into impact.
A flat or shallow rooflight takes rain almost perpendicular. Every drop lands squarely, transferring its full momentum into the panel, and the panel is directly above a room with nothing between it and the occupant.
That is the whole of the difference. It is geometry rather than a defect in the product.
The panel is a drum
A sheet of material fixed round its edges and struck in the middle behaves like a drum skin. It flexes, it radiates that flex as sound into the air below, and its stiffness and mass decide how loudly.
Light and flexible is loud. Heavy and stiff is quiet. That single principle explains every comparison on this page.
Why an old dome is the worst case
An acrylic or polycarbonate dome is the lightest, thinnest, most flexible thing that gets put over a roof opening, and it is unsupported across its whole span.
It is also, on a twenty five year old unit, brittle and dried out by ultraviolet, which raises the pitch of the sound it makes. A twin skin polycarbonate is a little better than a single skin because the air gap and the second sheet damp it slightly, and both are considerably louder than glass.
Almost everybody who replaces a 1980s dome with a modern glass unit mentions the drop in noise afterwards, frequently before they mention the light.
What glass does about it
| Unit | Why | Noise |
|---|---|---|
| Single skin polycarbonate dome | Light, thin, flexible | Loudest |
| Twin skin polycarbonate | Slight damping from the cavity | Very loud |
| Double glazed, both panes toughened | Mass, and two panes with a gas cavity | Much quieter |
| Double glazed, laminated inner | The interlayer damps the panel | Quieter again |
| Laminated with an acoustic interlayer | Interlayer tuned for damping | Quietest |

Laminate, and why it does more than its thickness suggests
A laminated pane is two sheets of glass bonded to a plastic interlayer. The interlayer is what does the acoustic work.
When the panel flexes, the two glass sheets try to slide across each other and the interlayer resists that movement viscously, turning vibration into a small amount of heat instead of into sound. It is the same principle as a damped panel anywhere in engineering.
The useful part is that laminate is already specified on any overhead unit for safety reasons, so the acoustic benefit arrives free with a specification you were going to write anyway. An acoustic grade interlayer improves on it further for a modest additional cost.
Asymmetric panes
A double glazed unit with two identical panes has two elements that resonate at the same frequency, and they reinforce each other.
Making the two panes different thicknesses moves their resonant frequencies apart so they no longer coincide, and the unit performs better acoustically than either pane would suggest. It is a standard technique in acoustic glazing and it costs very little to specify.
On an overhead unit the inner pane is laminated in any case, which already makes the two dissimilar. Asking for a genuinely asymmetric build takes it further.
Triple glazing is not the answer
People assume a third pane must be quieter, and for rain noise it frequently is not.
Three panes with two narrow cavities can behave worse acoustically than two panes with one wider cavity, because narrow cavities couple the panes together rather than isolating them. Triple glazing is specified for thermal performance, and where noise is the objective the money is better spent on laminate and asymmetry.
It also adds weight to the frame, which on a large overhead unit is a real consideration.
Pitch, and letting the water run
The angle at which rain meets the glass changes the impact, and steeper is quieter.
A unit set at a genuine pitch takes rain at an angle rather than square on, and the water begins to run rather than pooling and being struck again. A lantern is noticeably quieter than a flat unit of the same glass specification for this reason alone.
On a flat roof the pitch available is small, and going from the bare minimum fall to a slightly more generous one helps a little. It is not usually enough on its own to change the character of the noise.
Size, and how much it matters
A larger panel is louder in absolute terms, because it collects more rain and radiates from a larger area.
It is also lower pitched, because a larger panel flexes at a lower frequency, and lower pitched sound is generally less irritating than the sharp patter of a small stiff panel. So two units of half the area are not necessarily quieter than one of the full area, and they will sound different.
This is rarely a reason to change the arrangement of glazing on a roof. It is worth knowing so that the result is not a surprise.

The room below does half the work
Everything above is about the panel. The room is the other half, and it is where most of the improvement is available after installation.
A kitchen extension with a hard floor, hard worktops, plaster walls and no soft furnishing is a reverberant room. Sound entering it is reflected repeatedly rather than absorbed, so the noise persists and builds. The same rooflight over a carpeted room with curtains and upholstery sounds markedly quieter.
Rugs, blinds, upholstered seating and anything soft on a wall all reduce it. So does a splayed reveal, which scatters sound arriving from the opening rather than directing it straight down.
Blinds
A blind fitted under a rooflight does a modest amount for noise, and it is not nothing.
A fabric blind absorbs some of the sound radiating off the glass and interrupts the direct path from panel to ear. It is not acoustic insulation and it will not turn a loud unit into a quiet one, and it does soften the sound.
Where a blind is going in anyway for glare or for privacy, the acoustic effect is a small bonus. It is not a reason to fit one on its own.
Hail, and the Channel squall
Ordinary rain is one thing, and this coast produces the other thing regularly.
Squally showers arriving off the Channel drop large drops at speed, frequently mixed with hail in spring and autumn, and the noise from that is a different order from steady rain. It is short lived, it is loud, and it is what people remember.
Nothing in a specification eliminates it. Laminated glass with an acoustic interlayer, over a room with some soft surfaces in it, reduces it from startling to noticeable, which is a real improvement and is not silence.
Where the sound gets in besides the glass
The panel is the obvious path and it is not the only one. Sound also arrives through the structure round the opening.
Rain striking the roof covering next to a rooflight vibrates the deck, and that vibration travels through the deck into the kerb, through the kerb into the frame, and radiates off the plasterboard of the reveal. On a lightweight deck with a hard covering this structure borne path can be a meaningful part of what is heard.
Insulation on the kerb face helps with it incidentally, because insulation between two rigid layers damps them. A reveal lined with plasterboard on a resilient fixing rather than screwed hard to the kerb helps more. Neither is usually specified for acoustics and both come free with details that are worth doing anyway.
Ventilation openings, and the path they leave
An opening rooflight has a gap round the opening light, closed by a gasket. When the unit is shut that gasket is the acoustic seal, and it is doing more work than people realise.
A fixed unit is quieter than an opening one of the same glass, because it has no opening light and no perimeter gasket to leak through. The difference is small on a good unit with sound gaskets and it grows as the gaskets age.
Where a room needs both quiet and ventilation, the usual answer is a fixed rooflight plus ventilation provided elsewhere, rather than an opening rooflight doing both jobs adequately.

What makes it worse over time
A unit that has become louder has usually developed a mechanical problem rather than an acoustic one.
Gaskets that have hardened with age no longer damp the panel edge, so the glass rings more freely in its frame. A fixing that has loosened lets a component rattle under impact. Debris on the glass, particularly grit, adds a sharper component to the sound.
Any of those is worth reporting, because they are early symptoms of something to attend to rather than acoustic characteristics to live with.
What a failed unit sounds like
Occasionally noise is diagnostic. A distinct rattle or tick under rain or wind, from one point rather than across the panel, is a loose component. A change in the note of the rain sound over a season frequently means a gasket has gone or a bead has lifted. Neither is normal and both are cheap to put right early.
The general drumming of rain on overhead glass, on the other hand, is the product working exactly as it always did.
What we would specify where noise matters
- Glass rather than any plastic, without exception.
- Laminated inner pane, which is already required for safety.
- An acoustic interlayer where the room is a bedroom or a quiet living space.
- Asymmetric pane thicknesses.
- The most pitch the roof will give.
- A splayed reveal where the ceiling is being formed anyway.
The first two are standard on anything we fit. Three, four and five are decisions taken at ordering. Six is a decision taken by whoever forms the ceiling, which is why it belongs in the conversation early.
Being straight about the result
It is worth setting the expectation honestly, because this is a characteristic rather than a fault.
A well specified glass rooflight over a room with some soft surfaces will be audible in heavy rain and unremarkable in ordinary rain. It will not be silent, and no product on the market is. Anybody promising silence over a flat roof in a Channel squall is describing something that does not exist.
What is achievable is the difference between a room people avoid when it rains and a room where the rain is pleasant to be under, and that difference is entirely a matter of specification.
What we ask first on a flat roof
We ask what the room below is used for before writing the glass specification, because a bedroom and a utility room deserve different answers. Where noise is a stated priority we specify the laminate accordingly and say what it will and will not achieve. Where an existing unit has become louder we look at the gaskets and the fixings rather than assuming the glass.
Rain on glass is physics. How much of it reaches you is a specification.
Thinking about this job? We survey across Worthing, West Sussex and the South Downs and give you a fixed price before any work starts, with a 10-year workmanship guarantee.