How much weight can a walk-on rooflight or skylight take?
Whatever it was designed for, with a substantial factor of safety on top. That is not evasion: there is no single figure for walk on glass because the capacity depends on the span, the support conditions and the build up. What a specification states is a distributed load and a concentrated point load, and a domestic panel comfortably exceeds ordinary use.
Two load cases
Distributed and concentrated, and both are checked.
A distributed load is weight spread across the panel. A concentrated load is a single point, and each governs a different aspect of the design.
Why the point load matters more
Because it is the demanding one.
A person standing on one foot puts their whole weight through a small area, and glass is far more sensitive to that than to the same weight spread out.
What a domestic terrace is designed to
Floor loading rather than roof loading.
A private terrace or balcony is designed as a floor, which is a substantially higher requirement than the roof loading a standard rooflight is specified against.
Where a higher figure applies
Shared and public areas.
A communal balcony, a walkway or anywhere with public access carries a higher design load, and specifying the domestic figure there is the error to avoid.
The factor of safety
Substantial, and deliberately so.
Glass is designed with a considerable margin over the stated load, because it is brittle and because the consequence of failure is severe.
Why the span is the real answer
Because capacity falls as the panel grows.
The same build up over a larger opening carries far less, which is why a capacity figure only means anything alongside a size.
The limits are on what is the maximum span for walk on glass.
Support on two edges or four
Changes it substantially.
A panel held on all four edges carries far more than the same panel on two, so the frame is part of the capacity rather than separate from it.

What deflection has to do with it
It usually governs before strength does.
A panel is rarely close to breaking under ordinary use, and the design limit is how much it may move, because a floor that flexes feels unsafe.
What movement people notice
Almost none, by design.
Limits are set so deflection is imperceptible underfoot, which is why a well specified panel feels like paving rather than like glass.
Where the load actually goes
Into the frame and then into the structure.
The panel is only as good as what it bears on, and a frame or a deck that moves under load undermines the glass however well specified it is.
That is on does a walk on rooflight need an engineer.
Furniture
Distributed, and unremarkable. A table and chairs on a terrace panel is well within the design case, and the only caution is a small hard foot concentrating load at a point.
A hot tub or a large planter
Not on the panel.
Very heavy permanent loads belong on the structure around the rooflight rather than on the glass, and that is a design decision rather than a caution.
A ladder foot
The one to watch on a terrace.
A ladder concentrates a great deal of load through two small feet, and it is stood on the paving rather than on the panel.
Dropped objects
An impact case rather than a load case.
A dropped tool or pot is a hard body impact, and that is what the sacrificial layer exists to absorb.
What happens is on what happens if walk on glass breaks.
Snow on top of it
Included in the design. Snow is a distributed load and it is checked alongside the imposed loading, which on a terrace is the smaller of the two anyway.

Vehicles
A different product entirely. Glass rated for vehicle loading exists and it is a specialist specification with a much deeper build up, and it is not a domestic walk on panel.
Post breakage capacity
Part of what makes it safe. A properly designed panel is required to remain safe to stand on after a layer has broken, so the stated capacity is not the whole of the reassurance.
Why is on is walk on glass safe.
How the figure is verified
By calculation and by test. Manufacturers design to standards and test their products under load and impact, and reputable ones publish what their panels have been tested to.
What to ask a supplier
The loading at your span. Not what the glass can take in general, but what this build up is rated for over this opening with this support, which is a question with a documented answer.
Fatigue and repeated loading
Not a concern in the way it is with metal.
Glass does not fatigue under repeated loading the way a steel component might, so a panel walked on daily for twenty years is in the same condition it started in.
What ages is the top surface and the perimeter seals rather than the structural capacity.
Temperature and the capacity
Accounted for in the design.
Glass and interlayers behave differently in heat, and structural interlayers are chosen so the assembly retains its stiffness at the temperatures a terrace reaches in summer.
What a sample calculation looks like
A page rather than a paragraph.
The span, the support, the load cases, the deflection limit and the resulting build up, set out so building control can check it and a future owner can read it.
The question we start with on walk on glass
We ask what the terrace will be used for before the panel is specified, because a private balcony and a shared walkway are different design loads and only one of them is the default.
The whole picture is on the walk on rooflight installation page.
Thinking about this job? We survey across Worthing, West Sussex and the South Downs and give you a fixed price before any work starts, with a 10-year workmanship guarantee.