Roof Window Installation

Can a roof window be fitted between trusses?

Yes, and on a trussed roof it is the only way it is done. A trussed rafter is an engineered component that is not cut, so the window fits within the clear space between two members. That sets a maximum width, and it rules very little out because most domestic roof windows are narrower than the space available.

Why a truss is not cut

Because it is designed as a single component in tension and compression.

A trussed rafter carries load through its webs and chords as a system, and removing any part of it removes capacity the rest of the roof was relying on.

Cutting one is a structural alteration requiring a designed replacement, not a carpentry decision.

What the spacing gives you

Standard centres of 600 millimetres are the usual assumption, and the clear space is less than that.

Subtract the thickness of the two members and any allowance for the frame and its fixings, and the clear width available is meaningfully narrower than the nominal centres.

Which is why the actual dimension is measured rather than assumed.

Why centres vary more than expected

Because they are set on site rather than in a factory.

Trusses are positioned by a carpenter to a nominal spacing, and the actual centres on a built roof vary, occasionally by enough to change which unit fits.

It is taken with a tape at survey, in the position the window is actually going.

What fits

Most standard roof windows in their narrower widths.

Manufacturers make widths specifically intended for between-truss installation, and those are the sizes that go into post-war and modern estate housing without any structural work at all.

The dimensions are on trussed rafters and the widths that fit between them.

What does not

Anything wider than the clear space, which includes most of the larger sizes.

A wide unit on a trussed roof means altering the trusses, which is a designed structural job rather than a rooflight one, and it is a different order of cost.

An opening formed in a pitched roof ready for a roof window, battens cut back and trimmers visible either side, underlay dressed around it, seen from outside
Two narrow units instead

Two narrow units instead

The usual answer, and frequently the better one.

Two units in adjacent truss bays give more glass than one wide one would, light the room more evenly, and need no structural work.

A combination flashing kit weathers the pair properly where they are close together.

Trimming above and below

Still required, and it is ordinary carpentry.

The window needs timbers across the top and bottom of the opening between the trusses, fixed to them, to carry the frame and support the covering battens.

That is trimming within the bay rather than altering the truss.

Where the webs get in the way

The constraint people meet on a standard fink truss.

The diagonal webs occupy the space inside the truss, and while they do not obstruct the roof plane, they make working in the loft awkward and can restrict access to the position.

They are also not cut, for the same reason the rafters are not.

Attic trusses

A different component entirely, and it changes everything.

An attic truss has a clear rectangular space designed into it and a bottom chord sized to carry a floor, so the roof space is usable and the window positions were frequently anticipated.

What that means is on the Southwater page.

A room in the roof

The question that follows, and the answer is generally no on a fink truss.

Making a trussed loft habitable means replacing what the webs do with a designed structure, which is a substantial job and a different conversation from a rooflight.

Which one a roof has takes five minutes at the loft hatch.

Cut roofs by contrast

Where the constraint largely disappears. A cut roof has rafters and purlins rather than engineered components, so a rafter can be trimmed with a designed opening and the width is not fixed by member spacing.

The purlin becomes the constraint instead of the spacing.

Close detail of lead soakers and an apron flashing being dressed into a Sussex clay peg tile roof around a roof window, the irregular hand made gauge of the tiles clearly visible
Telling them apart

Telling them apart

Straightforward once you know what to look for.

Trusses are lightweight members joined by metal plates, arriving as prefabricated triangles. A cut roof is heavier timber, jointed and nailed on site, with purlins running along the building.

It is a five minute check and it decides the whole conversation.

Where the position can move

Along the bay rather than across it.

A window can sit anywhere up or down the slope within a bay, so the position is adjusted vertically to suit the room, the eaves and any escape requirement.

Sideways it goes in the next bay or not at all.

Insulation and services in the way

The practical check inside the bay. Cables, pipework and sometimes a water tank occupy roof spaces, and a bay that is clear on the roof plane can be obstructed inside.

The loft is walked rather than glanced into before a position is agreed.

What it means for a modern house

Almost nothing, because the sizes suit.

Post-war and modern estate housing is trussed throughout, and the between-truss widths cover what most rooms want. It constrains the maximum rather than preventing the work.

Metal plate connectors

A detail worth knowing about, because it explains why trusses are so unforgiving.

The joints in a trussed rafter are made with toothed metal plates pressed into the timber under factory conditions, and their capacity depends on that full contact.

Which is why a truss cannot be modified on site and repaired with a nailed splice: the joint is doing something a carpenter cannot reproduce with a hammer.

What we measure on a pitched roof

We measure the actual centres in the position the window is going, rather than assuming a nominal figure, and we propose two units in adjacent bays rather than altering a truss.

The whole picture is on the roof window installation page.

Thinking about this job? We survey across Worthing, West Sussex and the South Downs and give you a fixed price before any work starts, with a 10-year workmanship guarantee.

Get a fixed quote

Get a fixed quote

Tell us about the roof. We will tell you the price.

A survey costs you nothing and there is no obligation attached to it. We look at the roof build-up, the exposure and the opening, and give you one fixed figure, not an estimate that moves once work starts.

If your rooflight is leaking now, say so and we will prioritise the survey.

  • Fixed price, confirmed in writing
  • 10-year workmanship guarantee
  • Installed to current Building Regulations
  • Your roof is never left open overnight
Call Get a fixed quote