Acoustic laminates under a flight path or beside the A27
A rooflight faces the sky, which is where aircraft are, and it sits in a roof, which on a road-side house is the surface with the clearest line to the traffic. Reducing external noise through it is possible and the mechanism is different from the one that reduces rain noise.
Two different noise problems
Rain on the glass is noise generated at the panel: drops striking it and the panel radiating that impact into the room. It is solved by damping the panel.
External noise is airborne sound arriving from outside and passing through the assembly. It is solved by making the assembly harder to pass through.
The two share one answer, laminate, for different reasons, and they differ on everything else. Rain noise has its own page; this one is the external case.
What actually stops airborne sound
Three properties, in roughly this order of usefulness on a rooflight.
- Mass. Heavier assemblies are harder for sound to move. Thicker glass performs better than thinner.
- Damping. A viscoelastic interlayer converts vibration into a small amount of heat instead of letting it pass.
- Asymmetry. Two panes of different thickness resonate at different frequencies, so they do not reinforce each other.
All three are available in a double glazed unit, and together they do considerably more than adding a third pane.
Why an acoustic laminate is different from a safety laminate
Every overhead unit has a laminated inner pane, for safety. That laminate already helps acoustically, because any interlayer damps the panel.
An acoustic laminate uses an interlayer formulated for damping rather than purely for structural retention. It is softer and more viscoelastic, so it converts more vibration and passes less.
It is the upgrade that does most for the money on a noise job, and it arrives on a specification you were writing anyway.
The coincidence dip
Worth knowing because it explains why glass sometimes performs worse than its thickness suggests.
Every pane has a frequency at which sound waves arriving at a particular angle match the natural bending waves in the glass. At that frequency the pane transmits far more readily than elsewhere, and the effect is called the coincidence dip.
Where it falls depends on the thickness of the pane. Two identical panes have their dip in the same place and reinforce it. Two panes of different thickness have dips in different places, so neither coincides with the other, and the assembly has no single weak frequency.
An acoustic interlayer also damps the resonance itself, which flattens the dip. That is why laminate and asymmetry together outperform either alone.

Traffic and aircraft are different spectra
| Road traffic | Aircraft | |
|---|---|---|
| Character | Continuous, low frequency dominated | Intermittent, broad, rises and falls |
| Direction at a rooflight | Mostly horizontal, arriving at a shallow angle | From above, close to normal to the glass |
| Hardest part | The low frequency rumble | The peak of each pass |
| Mass helps | Yes, and low frequencies are the hardest to stop | Yes |
| Rooflight is | Not usually the weakest element | Frequently the most exposed element |
The last row is the important one. Beside a road, the walls and the windows facing the road matter more than the roof. Under a flight path, the roof is the surface pointing at the source.
Under a flight path
Aircraft noise arrives from above, close to perpendicular to a flat rooflight, which is the angle at which glazing performs least well.
It is also broadband and it has a peak that rises and falls over perhaps thirty seconds, which the ear notices far more than a steady background at the same average level. A room can be perfectly quiet on average and still be interrupted regularly.
Locally that means the approaches to Gatwick over the Weald, and the circuit at Shoreham, which is low level and close. In both, a rooflight is genuinely the exposed element and an acoustic specification is worth having.
Beside the A27
The A27 runs the length of our patch, past Worthing, Lancing, Shoreham and up toward Arundel, and it is a continuous source rather than an intermittent one.
Traffic noise is dominated by low frequencies, which are the hardest to stop with any glazing, and it arrives mostly horizontally. On a house beside it, the elevation facing the road is doing most of the work and a roof is comparatively sheltered.
Which means an acoustic rooflight beside the A27 is worth specifying and is unlikely to be the thing that transforms the house. Where the road-facing windows are ordinary double glazing, they are the place to start.
The weakest element decides the room
This is the principle that governs whether any of this is worth doing.
Sound finds the easiest path. Fitting an excellent acoustic rooflight into a room with a single glazed window, an unsealed loft hatch or an uninsulated wall improves that room very little, because the sound is coming in somewhere else.
Acoustic performance is decided by the worst element rather than the best, which is why a whole room has to be considered rather than one component. Where the rooflight genuinely is the worst element, upgrading it works. Where it is not, it is money spent on the wrong surface.
Air paths matter more than glass
A small gap passes a surprising amount of sound, and this is where a good deal of noise actually arrives.
An open trickle vent is an air path and therefore a sound path. A hardened gasket on an opening rooflight is a gap all the way round. An unsealed cable penetration or a poorly sealed reveal is another.
Which produces an awkward conflict: a trickle vent is providing the background ventilation the room needs, and it is passing sound. Acoustic trickle vents exist and are a partial answer. On a badly affected room, mechanical ventilation with the vents closed is the arrangement that actually works.

The frame and the reveal
Sound also travels through the structure rather than the air, and around a rooflight there is a path worth knowing.
Noise striking the roof covering vibrates the deck, which passes into the kerb or the trimmers, into the frame, and radiates off the plasterboard of the reveal into the room. On a lightweight roof that structure borne path can be a meaningful part of what is heard.
Insulation on the kerb face helps incidentally, because insulation between two rigid layers damps them. A reveal lined on a resilient fixing rather than screwed hard to the structure helps more. Neither is usually specified for acoustics and both come free with details worth doing anyway.
Fixed against opening
A fixed rooflight outperforms an opening one acoustically, and by more than people expect.
An opening unit has an opening light with a perimeter gasket, and that gasket is the acoustic seal. When it is new and compressed properly the difference is modest. As it hardens, the difference grows.
Where a room is noise sensitive and ventilation comes from elsewhere, a fixed unit is the better specification. Where ventilation is needed, an opening unit with good gaskets, kept in good order, is the right answer.
Triple glazing, again
A third pane contributes to acoustic performance and it is not the efficient way to buy it.
Two panes with one wider cavity generally outperform three panes with two narrow ones, because narrow cavities couple the panes together. And the third pane adds weight overhead, which brings the constraints the triple glazing page sets out.
The money goes further on an acoustic laminate and asymmetric panes. Where a specification already has both and more is wanted, a third pane is then worth considering.
What the numbers mean
Acoustic performance is quoted as a weighted sound reduction index, a single figure in decibels, sometimes with correction terms for traffic and other spectra.
Two things are worth knowing about it. It describes the glazing in a laboratory rather than the assembly in your roof, so the installed performance is lower. And a difference of a couple of decibels between two products is not something anybody hears, whereas a difference of ten is substantial.
Where the correction terms are quoted, the traffic-corrected figure is the one to compare for a road, because it weights the low frequencies that traffic actually produces.
What it can realistically achieve
Setting expectations honestly, because this is an area where they are routinely oversold.
A well specified acoustic rooflight in a room where it is the weakest element makes a genuine, noticeable difference: aircraft passes become a muted presence rather than an interruption, and traffic becomes a background rather than a feature.
It does not make a room silent, and nothing available does. A room under a flight path with acoustic glazing is a quieter room under a flight path.

Where it is worth the money
- A bedroom under a flight path, which is the clearest case there is.
- A home office or a study where concentration matters.
- A loft conversion, where the roof is the whole envelope and the rooflight is a large part of it.
- Any room where the rooflight is genuinely the weakest acoustic element.
And where it is not: a kitchen extension beside a road whose road-facing windows are ordinary double glazing, where the money goes into those first.
Blinds, and what they do for noise
People ask, and the answer is a small honest amount rather than nothing.
A fabric blind absorbs some of the sound radiating off the inner pane and interrupts the direct path from glass to ear. It also adds a soft surface to a room that is frequently otherwise hard, which reduces the reverberation that makes any noise persist.
It is not acoustic insulation and it will not turn a loud room into a quiet one. Where a blind is going in anyway for glare or blackout, the acoustic effect is a small bonus rather than a reason to fit one.
The room itself does half of it
Two rooms with identical rooflights sound different, and the difference is what is in them.
A kitchen extension with a hard floor, hard worktops, plaster walls and no soft furnishing is reverberant: sound entering it is reflected repeatedly rather than absorbed, so it persists and builds. The same noise entering a carpeted room with curtains and upholstery is absorbed and sounds markedly quieter.
Which means some of what gets diagnosed as a glazing problem is a room acoustics problem, and rugs, blinds and soft seating are a cheaper first move than new glass. It is worth trying before spending.
Retrofitting
Where a room is already noisy, the options depend on the unit.
Where the frame is designed to be reglazed and the rebate takes the thickness, the sealed unit can sometimes be changed for an acoustic one. Where it is not, it is a whole unit replacement.
Before either, the cheap checks are worth doing: the gasket condition, the trickle vent, the reveal seal and any cable penetration. On an older unit a hardened gasket is frequently a substantial part of the problem and a fraction of the cost of new glass.
What we want to know on the glazing
We ask what the noise actually is and when, because aircraft and traffic want different specifications and rain is a different problem again. We look at the whole room rather than the rooflight alone, and say when the window facing the road is the thing to change rather than the roof. Where the rooflight is the exposed element we specify an acoustic laminate and asymmetric panes, which is where the value is.
Sound finds the easiest path. Upgrading anything other than the easiest path changes very little.
Thinking about this job? We survey across Worthing, West Sussex and the South Downs and give you a fixed price before any work starts, with a 10-year workmanship guarantee.